After struggling quite a bit with the DIY tube-coupler and in the interest of making my graphs compatible with other graphs out there for easy comparison, I decided to get an IEC6038-4/IEC60711/IEC711 coupler. This is a Chinese knockoff which is supposed to be pretty close to the real deal.
To understand this, we need to first understand how records are mixed and mastered.
Mixing is the process of taking raw recorded tracks and using tools like compression, EQ and reverb along with adjusting levels and panning to create a finished stereo mix.
Mastering is the final step in the production process that takes the finished stereo mix and optimizes it for playback on a variety of devices.
EQing individual instruments
Mix engineers first work on the individual tracks to make them sound right and then put them together to make a record. For acoustic music, the mix engineers (especially when they are also the producers or have access) sometimes go into the recording booth to hear what an instrument actually sounds like and then try to replicate that while mixing with the instruments raw tracks using EQ (among other things) before putting all the tracks together to create the final record. The important thing to note here is that the EQ is done for each individual instrument.
Earphones and Headphones as EQ
One way to think about the things in your chain when listening to music, is to think of them as EQ devices (among other things). A colored earphone/headphone in that sense is the same as applying EQ but this EQ is done on the final record (similar to mastering) and there’s a reason the first rule of mastering is “do no harm” and why mastering is all about making subtle changes. An EQ applied to the final record is destructive, especially for well recorded acoustic music where authentic replay matters, because it changes the sound of the individual instruments in different ways and an EQ that works for one instrument might not work for another.
This is also the reason why most earphones and headphones (since they are all colored in some way, some more than others) can’t do justice to all instruments and can at best be good for certain instruments on certain records, and why neutrally-tuned earphones and headphones might be better for well-recorded acoustic music where authentic replay matters (for some definition of neutral, which is a post for another day 🙂).
If you enjoyed reading this, please consider subscribing to the blog with your email to get notified as soon as I make future posts:
These measurements are made on my DIY IEM measurement rig and are not accurate, and don’t necessarily represent what you might hear, especially before 60 Hz (huge sub-base roll-off) and after 10 kHz (and maybe even after 3 kHz as my ER2XR graph is very different compared to Crinacle’s post that). You can use it just to get a comparative idea, hence the comparison with ER2XR to give you a point of reference. Improving the rig is an ongoing process.
Here is Crinacle’s ER2XR graph for reference
It looks like final went with the mids to bass rise like in the E series and the highs of the A8000 on A4000.
In addition to its extensive hearing and testing products, Illinois-based Etymotic has won over the hearts of many audiophiles with their ER line of earphones. Lead Engineer Dave Friesema chats with us to discuss the company’s design approach to balanced armature headphones, consumer research and what’s next for the future of headphones.
He has worked on the ER MMCX series (ER4, ER3, ER2), the first Bluetooth series, HF series and the MC series.
He is the project manager for the ER MMCX series.
He was a fan of the original ER4 before working at Etymotic.
It’s a company of engineers.
They have always been a measurement heavy company and use KEMAR mannequins and lots of (single cavity) ear simulators (while at the desk).
They have their target for what they consider accurate.
Those who have been at the company for a long time know what the ear canal resonance is and they know what the right answer is at this point i.e., 15dB resonance between 2.6 – 2.8khz for insert earphones since the ear-canal is not flat and has this resonance built in. When sound hits your eardrums this resonance is built in so for insert earphones you have shifted that resonance so you have to put it back.
Etymotic has always been about hitting targets and is mathematical about it but they give importance to listening because you can’t hear with your eyes.
Lots of people in the company have good ears and their inputs are taken.
Etymotic traditionally moves very slowly.
On Keeping Things Simple
Etymotic has always been a single driver (no crossover) earphone company but it’s not to say they would never do multi-drivers. Dave can’t imagine doing something with 10 drivers but if he had to go down that path he would just use 2,3 or 4 drivers.
If you’re just putting in redundancy by taking the same driver and using two of them to cover the same frequency range, all you are doing is adding sensitivity and you’re not driving that large of a volume into the ear canal.
You don’t really need something that is a 120 dB sensitive with a 100 mW drive. You’ll just blow your ears out.
If you have an accurate earphone then everything sounds the way it’s supposed to sound. As a guitar player you want your guitar to sound the way you are used to hearing them. You don’t want the frequency response massively changed to emphasize the frequencies of the guitar, you want it to sit in the mix the way you’re used to hearing it.
Years ago they used to go to trade shows and take the KEMAR mannequins with them. Somebody could bring their own earphone and they could play their own music that they would record through the KEMAR and then they would take the recording and play it again and repeat the process 3 times (like taking a photocopy of a photocopy of a photocopy). At the end of 3 loops the Etymotics would sound more or less the same (not perfect though) but with the colored earphones it would make a huge difference after just 3 loops. Either it would sound like it’s totally under water or thin and bright. Every coloration was emphasized with each replication.
On The New ER4 MMCX Series
Dave wanted to improve a few things with the original 4:
4S was fairly inefficient (100 ohms).
4P was more efficient and had lower impedance. When impedance goes down it tilts the frequency response so the 4P was considered a bass-boosted version but it wasn’t really. It just had a tilted frequency response where the bass and lower mid-range tiled up a little bit and the peak and higher frequencies tilted down a little bit. It was warmer and wasn’t as detailed as the 4S.
With the new ER4SR they tweaked it to bring the accuracy where they wanted, making it more accurate than the original 4S and they were able to drop the impedance to 45ohms.
For the ER4XR they went with a different driver to hit the same mid-range and high frequency and get an actual bass-boost (instead of just tilting the frequency response) without compromising the mid-range and treble for it.
Studio (Reference|Edition) Series Vs. Extended Response Series
The Studio series (SR/SE) is accurate throughout and is flat in the bass
The Extended Response (XR) series is about making it as accurate as they could in the mid-range and higher frequencies with a little bit of low-end boost.
In the ER4 and ER3 there were excursion limits to the BA driver and it wasn’t easy to add 10 dB of bass boost (it was more closer to 4 dB).
With ER2 which is a moving coil driver they could have added more bass but they kept it modest which is also a big change for them.
On Why Insertion Depth Is Important
Makes big difference to higher frequencies.
You avoid the occlusion effect with deep insertion.
They source BA drivers from different people and they are all slightly customized but he won’t say if they are Knowles drives.
There are very few companies that manufacturer BA drivers and do it well because setting up the tooling for it is not an inconsequential thing (high-precision assembly and expensive).
BA drivers come in standard sizes and there’s customization that can be done within it.
On Future Plans
There might not be more earphone in the ER MMCX series. They went with a good (ER2), better (ER3), best (ER4) family in the series.
They might look at adding a higher end earphone as part of a different series.
No plans for circumaural and supra aural headphones.
Bluetooth stuff is disposable electronics. Etymotic users are about buying a few earphones and keeping it for years.
MC and MK series are the other moving coil driver earphone along with ER2.
To start with I had very high expectations from the final A4000 with some early reviews calling it a “baby A8000”, the A8000 being final’s flagship earphone that cost $2000. Given my experience with some earphones from final’s E-Series (E500 and E3000) that seemed very pleasant and maturely tuned but lacked both in quantity and quality in the highs for my preference and the fact that final is one of those few companies that seems to be very passionate about what they do, I was really hoping to find a final earphone that came close to my preference. So clearly I was going into this very biased.
Before I share my initial impressions it’s important to understand some context. At this point my reference earphone is the Etymotic ER2XR and I would classify myself as being a neutral-head. I listen to any and all types of music but I generally stay away from most forms of electronic music. I’m listening to music from Spotify (very high quality – downlaoded) on the Sony NW-A105. These impressions are OOTB (Out Of The Box) with no burn-in and I’ve listened to them for a couple of hours. final recommends 150 to 200 hours of normal-usage burn-in which according to them is primarily for the adhesive in the driver unit as it may affect the slight movement of the diaphragm and usage over time might allow it to move more freely.
With that out the way, here are my initial impressions:
The first thing I noticed is the bass. It is slightly more than on the ER2XR but the delta feels like it’s a lot more than it actually is because of the emphasis in the mid-bass on the A4000. This gives it more thump and makes it punchier compared to ER2XR (which has a sub-bass emphasis with a lot more rumble and comes across as cleaner and leaner).
Mids and vocals seem more forward on the A4000 and also very slightly cleaner.
The A4000 has a noticeable boost in the highs compared to the ER2XR but without sounding harsh to me. You can “hear the metal” of the instruments on the A4000 without any resonances that might make it sound metallic. This area might be problematic for some people as I’ve seen tolerances vary a lot when it comes to higher frequencies.
Imaging and separation seems to be slightly better on the A4000 while transient response is slightly slower compared to ER2XR.
Need to spend more time with them to say anything about resolution/detail retrieval as they seem very close.
These are power hunger with only 18 ohms of impedance but a sensitivity of 100 dB/mW and require similar power as the ER2XR which has an impedance of 15 Ohms and sensitivity of 96 dB at 0.1v (98 dB/mW )
The A4000 is super light, fits very well in my ears and is super comfortable for me, but the cable is very thin (above the y-split) and I feel like I’m going to break it every time I take them of while holding it just above the 2-pin connector.
If you prefer a dark and smooth sound, the A4000 might not be for you.
Overall I think it has a well balanced sound signature, sounds very coherent, has great timbre for most instruments and is more “fun” than the ER2XR on most tracks, which is not necessarily a good or bad thing, just different and I think they compliment each other well.
These are very early impressions so take them FWIW. My impressions might change after I spend more time with them and get some “brain burn-in”.
P.S. I haven’t heard the A8000 so can’t confirm the “baby A8000” claim.
That’s all for now. I’ll be doing a listening session post with these soon, so subscribe to the blog with your email to get notified as soon as I make future posts: